ServicesDent Repair
Dent Repair in Yosemite Lakes
Most dents can be fixed one of two ways: pushed back out from behind with the factory paint intact, or worked, filled and refinished. We look at your car, tell you which method fits each dent and why, and then do the repair at our shop.

What dent repair actually involves
Sheet metal has memory. When a panel is pushed in without being stretched or creased too sharply, it can often be massaged back to its original shape. That is the idea behind paintless dent repair, or PDR: a technician reaches behind the panel with steel rods and picks, or pulls from the front with glue tabs, and works the low spot up in small steps until it is level under a reflection board.
PDR only works when the paint is unbroken and the metal is not stretched. If the clearcoat is cracked, the dent sits on a sharp body line, or the metal has been folded, we move to conventional repair: pull the dent, shape the panel with hammer and dolly, apply a thin skim of body filler, then prime, base coat and clear. That refinished area is covered by our lifetime warranty on all paint work.
Steel and aluminum also behave differently. Aluminum hoods and fenders, common on newer trucks and SUVs, are stiffer, work-harden faster and need more patience and heat control. We tell you which material your panel is before we quote the repair.
What we do on a dent repair
- Inspection under proper light
- We check every dent under a line board or LED panel, which shows low spots and high spots your eye misses in daylight. We also look for paint cracks that rule out PDR.
- Access and trim removal
- Reaching the back of a dent often means removing a tail light, door trim panel or inner fender liner. We pull those parts carefully and reinstall the clips and fasteners so nothing rattles afterward.
- Paintless dent repair
- For eligible dents we push or pull the metal back to shape and keep the factory finish. No filler, no paint, and no color match to worry about.
- Conventional dent repair and refinish
- When PDR is not possible we straighten the metal, use as little filler as the panel needs, and refinish the area with primer, matched base coat and clear. We blend into adjacent panels when that is needed for the color to read evenly.
- Final check
- Before you pick up your car we look at the repaired panel again under the same light we used for the inspection, so you see what we see.
Signs a dent needs more than waiting
Cracked or flaking paint around the dent
Once the clearcoat breaks, moisture reaches the primer and bare steel underneath. Rust starts at the edge of the crack and spreads under the paint, which turns a small repair into a larger one.
A crease along a body line
Dents that cross a sharp styling line stretch the metal. These rarely come out cleanly with PDR alone and usually need shaping and refinish.
Many small round dents on the roof and hood
That pattern points to hail. These are often good PDR candidates, and the insurance claim is usually handled under comprehensive coverage.
A door that sounds or closes differently
A dent near the door edge or hinge can bend the inner frame of the door. If the gap looks uneven or the door catches, the damage may go past the outer skin, and we may suggest our collision repair work instead.
A dent in a bumper cover
Plastic bumper covers do not respond to PDR tools like steel does. They are handled with heat and plastic repair, which we cover on our bumper repair page.
How a dent repair goes at our shop
- 1
You describe the damage by phone
Tell us where the dent is, how it happened and whether the paint is broken. That helps us judge whether it is likely a PDR job before you drive in.
- 2
We inspect and write the estimate
At the shop we check each dent under light, confirm steel or aluminum, and note which trim has to come off. The estimate lists each dent and the method we plan to use.
- 3
The repair
Small PDR repairs usually stay in one stage of work. Refinished dents take longer because primer and clearcoat need time to cure before they are sanded and polished.
- 4
Pickup and walkthrough
We show you the panel, explain what was done, and point out anything we noticed that you may want to watch later.

What moves the price of dent repair
Dent repair is priced dent by dent, not by the hour you wait. The biggest single factor is whether the paint survived. After that, size, location and access do most of the work.
- Paint intact or broken
- PDR avoids filler, primer, paint and clear, so it typically costs less than a refinished repair of the same dent. Broken paint means materials and cure time are added.
- Size and depth
- A shallow dime-sized ding takes far less time than a deep dent the size of a palm, which stretches more metal.
- Location and access
- Dents near edges, on body lines or behind roof braces take more work. If trim, headliner or lights must come off to reach the back, that labor is part of the estimate.
- Panel material
- Aluminum panels take more time than steel because the metal resists reshaping and can crack if pushed too fast.
- Color blending
- Metallic and pearl colors often need blending into the next panel so the repair does not show at an angle, which adds refinish time.
Dent repair questions we hear
Something not covered here? (559) 616-8794
Can every dent be fixed with paintless dent repair?
No. PDR needs unbroken paint, metal that is not sharply creased, and a way to reach or pull the dent. Many door dings and hail dents qualify. Deep creases, dents on panel edges and anything with cracked paint usually need conventional repair.
Will a refinished dent match the rest of my car?
We mix the color from your paint code and adjust it to how your paint has aged, then blend into nearby panels when needed. The work carries our lifetime warranty on all paint work.
Should I file an insurance claim for a dent?
It depends on your deductible and the cause. A single parking lot ding is often cheaper to pay for directly, while hail damage across the roof and hood is usually worth a comprehensive claim. Our insurance claims page explains how that process works with us.
Is it a problem if I just leave a small dent alone?
If the paint is intact, a small dent is mostly cosmetic. If the paint is chipped or cracked, rust can start at bare metal, so it is worth repairing before it spreads.
How long will my car be at the shop?
Simple PDR work is usually quick. A dent that gets filler and refinish stays longer, since primer, base coat and clear each sit for a set time before the next step or before sanding and polishing. The estimate includes the timeline we expect for your car.

Find out which repair your dent needs
Give us the location of the dent and whether the paint around it is chipped, cracked or still smooth. We will say whether PDR is likely, walk you through what conventional repair would mean, and suggest a good time to bring your car in.